top of page

Selbsthilfegruppe

Öffentlich·35 Mitglieder
Mat Angiwan III
Mat Angiwan III

Repair 2911 Format Flash Driverar


How to Repair 2911 Format Flash Driverar in 3 Easy Steps




If you have a Cisco 2911 router that needs to be formatted, you might encounter a problem with the flash drive. The flash drive is a small storage device that holds the router's operating system and configuration files. Sometimes, the flash drive can get damaged or corrupted due to various reasons, such as power surges, improper shutdowns, or physical damage. When this happens, you might see an error message like "Repair 2911 Format Flash Driverar" when you try to boot up the router.


Download Zip: https://occiahymu.blogspot.com/?download=2w43Xu


Fortunately, there is a way to fix this problem and restore your router to its normal functioning. In this article, we will show you how to repair 2911 format flash driverar in 3 easy steps. You will need a computer with a serial port, a console cable, and a USB flash drive with at least 256 MB of free space.


Step 1: Connect the Console Cable




The first step is to connect the console cable between your computer and the router. The console cable is a special cable that allows you to access the router's command-line interface (CLI) through a terminal program on your computer. You can use any terminal program that supports serial communication, such as PuTTY, HyperTerminal, or Tera Term.


To connect the console cable, follow these steps:


  • Plug one end of the console cable into the serial port of your computer.



  • Plug the other end of the console cable into the console port of the router. The console port is usually located at the back of the router and labeled as "CONSOLE".



  • Turn on your computer and launch your terminal program.



  • Configure your terminal program with the following settings: baud rate = 9600, data bits = 8, parity = none, stop bits = 1, flow control = none.



  • Press Enter a few times until you see the router's prompt.



Step 2: Format the Flash Drive




The next step is to format the flash drive using the router's CLI. Formatting the flash drive will erase all the data on it and prepare it for installing a new operating system and configuration files. To format the flash drive, follow these steps:


  • Insert the USB flash drive into the USB port of the router. The USB port is usually located at the front of the router and labeled as "USB".



  • Enter the privileged EXEC mode by typing "enable" and pressing Enter. You might be asked for a password. If you don't know the password, you can try the default one, which is "cisco".



  • Enter the global configuration mode by typing "configure terminal" and pressing Enter.



  • Enter the command "format usbflash0:" and press Enter. This will format the USB flash drive as usbflash0, which is the name of the flash device on the router.



  • Confirm the format by typing "y" and pressing Enter. The format process will take a few minutes to complete.



  • Exit the global configuration mode by typing "end" and pressing Enter.



Step 3: Copy the Operating System and Configuration Files




The final step is to copy the operating system and configuration files from your computer to the USB flash drive. You will need to download these files from Cisco's website or from another source. The operating system file is usually called IOS (Internetwork Operating System) and has a .bin extension. The configuration file is usually called startup-config and has a .txt extension.


To copy these files, follow these steps:


  • On your computer, locate the IOS and startup-config files that you want to copy.



  • On your terminal program, enter the copy mode by typing "copy xmodem: usbflash0:" and pressing Enter. This will copy files from your computer's serial port (xmodem) to the USB flash drive (usbflash0).



  • Select the IOS file on your computer and start sending it through your terminal program. The exact procedure may vary depending on your terminal program, but usually you can use a menu option or a keyboard shortcut to send a file.



  • Wait until the IOS file is copied completely. This may take several minutes depending on the size of the file and the speed of your connection.



  • Select the startup-config file on your computer and start sending it through your terminal program.



  • Wait until the startup-config file is copied completely.



  • Exit the copy mode by typing "Ctrl-C" on your terminal program.



Congratulations, you have successfully repaired 2911 format flash driverar. You can now reboot your router and enjoy its normal functioning. To reboot your router, enter the command "reload" and press Enter. Confirm the reload by typing "y" and pressing Enter.


We hope this article was helpful and informative. If you have any questions or comments, please feel free to leave them below. Thank you for reading!


Info

Willkommen in der Gruppe! Hier können Sie sich mit anderen M...
FB_IMG_1666602945654(1).jpg
bottom of page